This is Page 2, continuing the Bolts 101 article. Here we discuss choices for bolts for an application. The previous post, Page 1 of Bolts 101, gives a ton of good background info, so we recommend reading that first, then this one on making a good bolt choice. Both pages focus on the practical side rather than on all the theoretical detail.
Link to yiyuan
The hard part is defining what bolts to choose for a given job. It is the hard part because the rules of thumb have lots of exceptions. Also, it is your judgement and responsibility for the bolt choice. If the joint is critical — especially if it is for safety — perhaps some engineering help is appropriate. However, in most cases you can follow these guidelines and feel quite comfortable in making the decisions. Just note the exceptions.
When mounting an object that comes with bolt holes, use the size of bolts recommended by the manufacturer. If the item does not have specific instructions telling you what bolts to use, then use a bolt size that fits nicely, and fills in the holes.
The caster shown in the photo is a good example. It has 4 slots that accept 3/8″ or 10 mm bolts nicely. Either size works as a bolt choice. Note: Because the holes are slots, washers support the nut.
If the holes are not defined for the bolt size, there are lots of other considerations to select the size.
Use a bolt that works well with the thickness of the materials to connect. If you are bolting thin sheet metal, then big diameter bolts will not make it more secure. In fact, when push comes to shove, the material will often fail near the bolts, so it is better to have several smaller fasteners than one large one.
A typical rule of thumb . . . Use a bolt diameter that is 1.5 – 2.5 times (up to three times) the thickness of the thinner material you are bolting together. So, for 1/8″ material, a 1/4″ diameter is often a good bolt choice. For 1/4″ thick material, perhaps a 3/8″ or 1/2″ bolt.
This guideline falls apart for very thin materials, and for really thick stuff. In both these cases – if the joint is critical – it is better to use more fasteners rather than bigger ones. Note: For thin materials, it is usually best to back the joint with thicker material, like washers, or face plates, then the rules can apply again.
What do the bolts need to do? Are they through bolts (bolt with a nut)? Or does the bolt go into a threaded hole? Maybe the threaded hole goes through? Or maybe it is blind (go into a threaded hole that does not go through)?
Most of the discussion in this article shows bolts with nuts (and washers), but there are a lot of applications where the threads exist in another part. Really, the discussion is almost the same either way. Trailer wheel bolts are a good example where some are bolts into a threaded hub, while other times they are studs with a nut. Read more in the Trailer Wheel Bolts article.
Anyway, function matters, and it is often connected with the other things on this page like Thread Engagement and Loading (both topics below). What do the bolts need to do? Hold stuff, yeah, but do think about what they are holding? How they are holding it? And, perhaps most important, how critical is it? The bolts you choose – grade, size, and number – should reflect what the bolts need to do.
We think about bolts often as the straight metal bars with threads, but some bolts are not straight – like U-Bolts. Yes, they are a different animal, but when we need them, they can sure make life easier. And, much of the discussion on this page applies as well to U-Bolts.
Have you ever noticed that bolts rarely appear with just one? How many bolts do you need?
When you bolt something, you are constraining it in one direction. Argumentatively, it constrains more with friction and extended face contact, but if you really want to hold the piece, it requires more bolts. 2 bolts constrain rotation, and at least 3 bolts (not in a line) for bending constraint. We often see sets of 4 because it is an easy pattern, and it constrains many things very well.
Place bolt patterns so the bolts are spread – within reason. Generally, more distance between them makes the connection stronger. From the standpoint of holding things down, more is merrier, but it also makes things harder to work with.
The other reason for more bolts is safety. If the connection involves safety, better to over-kill.
The image here of the hitch illustrates some of these bolt choice factors. Bolt size is 1/2″ (defined by the hitch holes) – which is a little more than 2.5 times material thickness (less than 3 times), so that is good in 3/16″ thick material. They are Grade 8 for strength because safety is definitely a concern. Fine thread with Nylock nuts for security in a vibration environment. The main connection forces are in shear, and they have sufficient distance for joint stability.
In the hitch example, there are 4 connections. Each bolt connects the materials twice, once on each side. The 4 connections are not linear, so it is good for stability in bending.
Choose the bolt strength based on what you are asking the bolt to do. For safety, think about higher strength bolts like Grade 8 or more. In shear forces, think about a diameter that will easily take the loads. With tension forces, thick about fine threads as well as higher grade material.
There are 2 ways to achieve higher strength. The first is the bolt material – the bolt grade. Second is the bolt diameter.
As a perspective, from the chart in Part 1, we see that (generalized) Grade 5 is about twice as strong as Grade 2. That is a great way to increase strength. Another big improvement is diameter. When we consider diameter, a 3/8″ bolt is more than twice the strength of a 1/4″ bolt. In fact, it takes a high grade socket head 1/4″ bolt to match a 3/8″ grade 2 bolt. Truly, diameter is also a major factor. Consider this when using Stainless Steel bolts.
Proper bolt choice for strength comes with a balance of the other factors on this page. Sometimes we want a less strong bolt for impact or yield considerations.
By the way, when calculating bolt strength, use the root diameter of the threads (smallest diameter inside the threads), not the full diameter of the bolt. Also, think safety factors – and use them generously.
Fine Thread or Coarse Thread? That is a good question without a definitive answer. Here are some considerations.
When choosing bolts, there is not a definitive criteria, so make a call based on the advantages.
For me, I tend to use Coarse threads for smaller bolts (1/4″, 6mm and smaller) most of the time. With larger bolts, I use fine threads in vibration situations and when clamping force is critical. On the folding trailer tongue, for instance, the clamping bolts are 1/2″-20 (fine thread). Grade 8 for strength over-kill. The pivot bolts are not tight (or it would not pivot), so they do not enter the calculation, but they are the same size and thread so everything matches. (And, use the same wrenches on everything.)
Adding to this discussion, if you need to tap a hole for a bolt, or if you need to add a thread with a die, it is a good idea to pick bolts and a thread pitch to match the tools you have.
How long is enough? How long is too much?
Long enough is when the threaded portion sticks through the nut with a couple threads out. Too long is when the unused end of the bolt interferes with something – or, when the bolt cannot completely tighten. Just right might be the bolt you have in the bin (because you don’t have to go buy something).
With that said, don’t be afraid to cut a bolt. If it is a little too long, cut it to be right, then finish the end. Likewise, if you need a long or custom bolt, make it with threaded rod. Read this full article on working with threaded rod.
Please remember the washers (if you need them) when thinking about length. Also, special nuts, like Nyloc nuts, require a little more length than standard ones.
For bolts threading into something (not a nut), the concept of “long enough” must also take into account the thread engagement which is our next bolt choice factor.
It is easy to think about bolts with nuts for fastening – especially for DIY. That makes things easy. However, once in a while, you need to tap a hole. Taps are pretty easy to use and, when done right, make great threads for screwing a bolt into. When making your own threads, here are some things to consider.
The rules of thumb for thread engagement involve the material the bolt is threading into as well as the bolt diameter. It is a ratio with thread engagement length as a function of the bolt diameter. For instance, 2x means the depth of thread engagement is twice the diameter of the bolt. In this case, for a 1/4″ bolt, thread engagement is 2x the diameter, or 1/2″. That is just an example.
In general, use 1x for steel bolts into steel threads. 1.5x minimum and preferably 2x or more for aluminum. Magnesium and high strength plastics are 2.5x or 3x.
Again, these are rules of thumb, and alloys of the materials act differently. For Bolts 101 just use these numbers as a perspectives in your bolt choice.
You will note that most nuts are less than the 1x stated above. That has a lot to do with the way threads are formed. Cutting threads with a tap is not as strong as roll forming threads. Again, just a perspective.
Where do you put the bolts when you are building something? While there are several ways that forces might interact with a bolt, some directions are definitely better than others. If you have a choice, think about bolt positions and force direction as well as convenience and access.
First choice is putting the bolts as Locators only. This works when the parts are pushing into each other and the bolts are only there to locate and hold the position. Not much bolt strength is required for this kind of joint. Although this is ideal, it is often not how the forces direct.
Second choice is putting the bolts in Shear. That means the forces want to cut the bolts. Look above at the hitch photo. Forces of pulling the trailer and braking are perpendicular to the bolts. That is shear. Bolts are very strong in shear, and even when not fully tight, they are still strong in shear. That said, the bolt must be sized for the forces, so strength and diameter are both important.
The last choice is bolts in Tension. I say it is last choice, but it is often the only option – or in the case of the blue trailer tongue hinge, it is the best option to meet other goals. Read the section about bolting in our review of the folding tongue for more explanation. In tension, the bolt relies on the the threads to carry the loads. When this is needed, use larger bolts, stronger bolts, and multiple bolts for best security.
The truth is, most bolting connections are not just one of these forces, they are a combination. And, often the forces change at different times, so take that all into account.
As an example, look at the caster photo. In a practical sense, the bolts are there primarily as locators. The wheels carry the loads to the flange, then the flange is against the steel support. In reality, there are also shear forces when the brake is on, or when twisting the caster. Then there are some tension forces when the wheel hits something (like a seam in a concrete floor).
Finally, sometimes forces reverse, like from Shear one way, to Shear the other. These oscillating or vibrating situations are the worst for bolt choice because they pose a challenge in keeping things tight. In these cases, we recommend using more bolts, fine threads, and perhaps especially, a method of vibration resistance. (Like locknuts or wires or cotter pin nuts, . . . .)
While it is not really the last thing to consider, the environment for the bolt is pretty important. See Page 1 of Bolts 101 about finishes for more information. Also, please see Page 3 for information about Stainless Steel bolts if your environment will include significant moisture or chemicals.
We often think of bolts in a classic way like so many of the images on this page. Bolt through a hole, and clamps tight. But there are other applications like the very top “feature” image. That bolt is sticking out using nuts to anchor it in place. The extending part uses the head and top portion of the bolt as a place to hook a spring.
The spring hook bolt as pretty normal clamping — with nuts on either side of the structure. But what about more difficult situations like bolting a trailer safety chain? What about chain held by a bolt? Note the intersecting chain links that will not allow the bolted chain link to set fast against the metal surface. It is hard to clamp the bolt solid because adjacent links are in the way. Bolt choice here is more about size and locking than about getting it properly tight.
In this case, washers are stacked to provide a foundation for clamping forces. (Washers with some grinding to fit the chain.) This can work, but when the bolts are not “tight”, they will move when yanked into service. Such situations are not necessarily bad, but certainly require added bolt strength (and size).
It is not just a bolt choice, but also a bolting choice. Sometimes re-thinking function is the better way, so the bolts are solidly tight. Here is an example. (See another example in the Chain Anchor System Free Plans Article.)
How much space do you allow for a bolt hole? A lot of DIY projects suffer from bolts that are either too loose in their holes, or too tight and hard to assemble. What is the happy medium?
The problem, honestly, is not usually the size of any given hole, but rather, the alignment of holes with respect to each other. If you do things DIY with a scribe and a drill press, sometimes the holes do not line up perfectly. Yeah, I am right there, so here is a post on Aligning Misaligned Holes.
Typically, I add something like 10% to 15% to the bolt diameter for the hole size. Example: 1/4″ bolt + 15% = 0.287″ so round to a 9/32″ drill = 0.281″ diameter. I tend to round down as the bolts get larger. Example: 1″ bolt + 15% = 1.15″. That would suggest a 1-1/8″ hole. To me, the 1/8″ hole is a little too loose (sloppy fit), so for bigger bolts, I make it more like 10%. Example: 1″ bolt + 10% = 1.1″ or with rounding = 1-3/32″ or even 1-1/16″.
A good rule of thumb is to add as much tolerance to the hole as you are able to hold in tolerance on the hole location.
As simple as bolts seem, there is actually a lot to know about them. This is a fairly simple overview as a Bolts 101 kind of DIY introduction. Yet, there is so much more to know. Fortunately, this is also a subject with a lot of great information on the web. Just search on the topics that you need to know. Things like “Bolt Thread Pitch” or “Bolt Shear Strength”. You will find a ton of great stuff in deeper detail.
Again, this article is an introduction with a practical spin rather than a scientific one. It is about bolt choice, specifically because the practical side seems to be missing on the bolting sites we have seen. Let us know if we have skipped something important.
When it comes to construction, manufacturing, machinery, or DIY projects, screws and bolts are the unsung heroes that hold everything together. While they may seem like minor components, choosing the right supplier can significantly impact the quality, durability, and safety of your project. This blog will walk you through the essentials of screw and bolt suppliers—what they offer, how to evaluate them, and why making the right choice is crucial.
Understanding Screws and Bolts
Screws and bolts are types of fasteners used to join materials together. Though often used interchangeably, they have distinct characteristics.
Screws are typically used to fasten materials by being turned into a material.
Bolts are used with a nut to secure parts together, usually requiring pre-drilled holes.
They come in various shapes, sizes, materials, and finishes depending on the application—ranging from wood screws and machine screws to carriage bolts and hex bolts.
If you are looking for more details, kindly visit Custom Bolt Manufacturer.
Why Choosing the Right Supplier Matters
Not all suppliers offer the same level of quality, service, or product variety. Here are a few reasons why selecting the right supplier is important:
Quality Assurance
Industrial applications often require fasteners that meet strict specifications. A reputable supplier ensures consistency in quality, which directly affects product performance and safety.
Wide Range of Products
A good supplier stocks various screw and bolt types, sizes, materials (steel, stainless steel, brass, etc.), and grades, saving you the trouble of sourcing from multiple vendors.
Certifications and Standards
Look for suppliers that provide products certified under international standards like ISO, ASTM, or DIN. This is especially important for construction and engineering firms.
Bulk Availability and Custom Orders
Suppliers should be able to fulfill large orders and also accommodate custom specifications, whether for industrial-scale needs or specialty hardware.
Competitive Pricing
Price plays a major role, particularly for contractors or manufacturers working on tight budgets. The right supplier offers competitive rates without compromising on quality.
Delivery and Logistics
Timely delivery is crucial in project timelines. Leading suppliers have efficient shipping and inventory systems that ensure quick and safe delivery.
Types of Screw and Bolt Suppliers
1. Manufacturers
These are companies that produce fasteners from raw materials. Purchasing directly from manufacturers can be cost-effective for bulk buyers.
2. Distributors and Wholesalers
These suppliers buy in bulk from manufacturers and sell to retailers or end-users. They usually have a wide range of stock and offer better customer service.
3. Retailers
Retailers cater to smaller buyers such as individuals or small contractors. You can find them in hardware stores or online platforms.
4. Online Marketplaces
Websites like Amazon, Alibaba, and industry-specific platforms allow you to compare multiple suppliers and products in one place.
Key Considerations When Choosing a Supplier
1. Product Range
Does the supplier carry the specific screws and bolts you need? Ensure they stock the right dimensions, thread types, and materials for your applications.
2. Material and Finish Options
Fasteners can be made from various materials including carbon steel, stainless steel, brass, and titanium. Finishes like zinc plating or black oxide affect corrosion resistance and appearance.
3. Customer Support
Responsive support is important when you're dealing with technical specs or large orders. Evaluate their customer service, return policy, and technical assistance options.
4. Minimum Order Quantity (MOQ)
Some suppliers have MOQs, which might not be suitable for small buyers. Confirm these terms before placing an order.
5. Customization Services
Do they offer custom manufacturing based on blueprints or samples? This is vital for OEMs or specific industrial projects.
6. Shipping and Delivery Time
Evaluate how quickly they can fulfill your orders, especially if you’re working on strict project deadlines. Check if they provide real-time tracking and international shipping.
Top Features to Look for in a Screw and Bolt Supplier
ISO or similar certification
In-house testing or third-party quality audits
Detailed product documentation (tensile strength, corrosion resistance, etc.)
Option to request product samples
Positive reviews and testimonials
Established industry reputation
Red Flags to Watch Out For
Vague product specifications
No testing or quality control documentation
Poor customer service
Inconsistent product supply
Overly low prices that seem too good to be true
Benefits of Long-Term Supplier Relationships
Forming a long-term relationship with a trusted supplier offers multiple benefits:
Better pricing through negotiated contracts
Priority during high-demand seasons
Consistency in quality and specifications
Faster service and easier communication
Access to new or custom products
Final Thoughts
Whether you’re a contractor, manufacturer, or hobbyist, choosing the right screw and bolt supplier can make a big difference in your project's success. Don’t base your decision solely on price. Look for suppliers with a strong reputation, broad product offerings, and a commitment to quality and service. Do your research, ask for samples, and always verify certifications.
Screws and bolts may be small, but they hold the big things together—so choose your supplier wisely.
Are you interested in learning more about metal stamping parts manufacturers? Contact us today to secure an expert consultation!