Brushed Spur Gear Motor Selection Guide: Torque, Speed, and Gear Ratio

17, Nov. 2026

 

Brushed Spur Gear Motor Selection Guide: Torque, Speed, and Gear Ratio

To select a brushed spur gear motor, start with the required output speed and load torque, then choose a gear ratio that lets the motor deliver both within its operating limits. A higher reduction ratio generally lowers output speed and raises available output torque, while gear losses mean the torque increase is less than the ratio alone suggests. For example, a motor turning at 6,000 rpm with a 30:1 reduction has an ideal output speed of 200 rpm before accounting for load and other losses. At Shunli Motor, we recommend evaluating the complete operating point—not selecting a motor by torque or speed in isolation.

You can find more information on our web, so please take a look.

Who This Guide Is For

This guide is for product designers, engineers, and purchasing teams comparing brushed spur gear motors for equipment such as small conveyors, feeders, actuators, dispensers, and powered mechanisms. It is especially useful when the application has a defined output speed but the required gear ratio or motor torque is not yet clear. The selection principles apply broadly, but the final choice depends on the actual load, power supply, operating pattern, and installation constraints.

How Torque, Speed, and Gear Ratio Relate

Gear ratio determines the speed reduction

A spur gear motor combines a brushed DC motor with a spur-gear reduction stage. Gear ratio is commonly expressed as the number of motor revolutions for one output-shaft revolution. With a 20:1 ratio, the motor must rotate approximately 20 times for the output shaft to rotate once, so the theoretical output speed is the motor speed divided by 20.

Use this relationship as a first estimate: output speed ≈ motor speed ÷ gear ratio. Actual speed varies with applied voltage, load, motor characteristics, and gearbox losses. If the speed requirement is strict, confirm the expected operating speed under the intended load rather than relying only on a no-load motor speed.

Reduction increases torque, with losses

In an ideal gearbox, output torque would equal motor torque multiplied by the gear ratio. In a real assembly, friction and other mechanical losses reduce the torque available at the output, so a more useful estimate is output torque ≈ motor torque × gear ratio × gearbox efficiency. Efficiency depends on the gearbox design and operating conditions; do not assume a specific value unless the supplier provides a relevant specification.

Torque and speed also connect through mechanical power: power = torque × angular speed. This means a gear ratio trades speed for torque rather than creating power. A motor selected for a high output torque at very low speed may still be unsuitable if the required load exceeds its thermal or electrical operating limits.

Selection Framework: From Application to Motor

1. Define the load and motion profile

Describe what the motor must move, how it is connected, and whether it starts against a load. Record the required output speed, estimated or measured load torque, direction of rotation, and any acceleration or stopping requirements. Also define how often the motor runs, how long each operating period lasts, and whether it must hold a load when power is removed.

For a rotating load, torque may come from friction, gravity, belt tension, or a driven mechanism. For a linear load, first convert the force and transmission geometry into an estimated shaft torque. If these values are uncertain, measure the existing mechanism or test a representative assembly; a motor specification alone cannot resolve an unknown load.

2. Calculate a starting gear ratio

Divide the motor’s expected loaded speed by the desired output speed to estimate the reduction ratio. For instance, if the selected motor is expected to run at 6,000 rpm under the intended operating condition and the application needs about 200 rpm, a ratio near 30:1 is a reasonable starting point. This is an illustrative calculation, not a performance claim for a particular Shunli Motor product.

Next, estimate output torque using the motor torque available at that speed and an appropriate gearbox efficiency supplied for the proposed configuration. Avoid using stall torque as the normal operating torque: stall describes a stopped motor under a particular electrical condition and can involve high current and heating. Confirm that the motor can start and run the actual load without relying on prolonged stall operation.

3. Check electrical and thermal limits

Match the motor’s rated voltage to the available power supply and check operating current at the expected load. Brushed DC motor speed and current change with load, while supply voltage, wiring, switching, and control settings can affect actual behavior. Ask for the relevant speed-torque and current information for the proposed motor and gearbox combination.

Shunli Motor are exported all over the world and different industries with quality first. Our belief is to provide our customers with more and better high value-added products. Let's create a better future together.

Duty cycle matters as much as peak demand. A short movement followed by a long rest can create a different thermal condition from continuous operation, even when both applications reach the same peak torque. Provide the supplier with the run time, rest time, starts per hour, ambient conditions, and any enclosure or ventilation constraints.

4. Verify the mechanical interface

Check output-shaft diameter and length, mounting dimensions, gearbox orientation, allowable radial or axial loading, and the connection to the driven part. A motor that meets the torque and speed target may still be unsuitable if the shaft or mounting arrangement does not fit. Confirm whether external loads are supported by the gearbox output or should be carried by separate bearings in the application.

Noise, backlash, and positioning behavior may also affect the decision. Spur gear stages are often considered for straightforward rotary power transmission, but they are not automatically the best choice where very low backlash, quiet operation, or precise positioning is essential. State these requirements explicitly so they can be evaluated with the correct configuration.

Types, Materials, and Configuration Considerations

Brushed spur gear motors are available in different motor sizes, gear ratios, shaft arrangements, and construction options. Gear materials and housing designs vary by product and application; the suitable choice depends on load, required service conditions, cost targets, and the supplier’s available configurations. Rather than assuming that one material is universally superior, compare the documented specifications for the candidate assembly.

Also consider whether the application needs a standalone motor, a gearbox and motor combination, or a configured assembly with a connector or mounting feature. Any customization can affect engineering review, tooling or component availability, and sourcing timelines. Confirm the exact configuration in the quotation and drawing before approving samples or production.

Common Selection Mistakes

  • Choosing by maximum torque alone: Check the torque available at the target speed and the motor’s operating limits.
  • Using no-load speed as working speed: Request or verify speed under the intended load and voltage.
  • Ignoring startup demand: A mechanism may need more torque to start than to keep moving.
  • Overlooking duty cycle: Repeated starts or long run periods can change heating and service requirements.
  • Assuming the gearbox multiplies torque without loss: Include gearbox efficiency when estimating output torque.
  • Leaving mechanical details until late: Verify the shaft, mounting, load direction, and space envelope before finalizing the selection.

Pricing, MOQ, and Lead-Time Considerations

Pricing depends on the motor and gearbox specification, order quantity, configuration, and any requested customization. Minimum order quantities and lead times can also vary with the selected components and production schedule, so they should be confirmed for the exact part number rather than assumed from a general product category. For an accurate quotation, provide forecast quantities, target delivery timing, and whether evaluation samples are required.

When comparing offers, review more than unit price. Check that each supplier is quoting the same voltage, ratio, output-shaft dimensions, operating requirements, and included accessories. A clear specification helps reduce the risk of comparing products that appear similar but are not mechanically or electrically equivalent.

Supplier Evaluation Checklist

Before placing an order, ask the supplier to confirm the proposed operating point and the evidence available for that configuration. Useful information includes motor voltage, expected loaded speed, output torque basis, current, duty assumptions, gearbox ratio, shaft and mounting drawings, and relevant mechanical load limits. If a value is estimated rather than guaranteed, ask for that distinction to be stated clearly.

At Shunli Motor, we can review the application details and discuss a suitable brushed spur gear motor configuration for your project. Share the required speed and torque, power supply, operating cycle, installation dimensions, and expected order quantity so our team can assess the request and clarify available options. Final suitability should be confirmed against the agreed specification and your application testing.

Key Takeaways and Next Steps

  • Choose a gear ratio from the required loaded output speed, then verify that the motor can supply the needed torque at that operating point.
  • Estimate output torque with gearbox efficiency included; do not treat the ideal ratio calculation as a guaranteed value.
  • Check voltage, current, duty cycle, startup load, shaft dimensions, mounting, and operating environment before final selection.
  • Request configuration-specific specifications and confirm MOQ, pricing, and lead time with the supplier.

The right brushed spur gear motor is the one that meets your application’s torque and speed needs while fitting its electrical, thermal, and mechanical constraints. Start by documenting the load and motion profile, calculate a preliminary ratio, and then validate the complete operating point with the supplier. Contact Shunli Motor with your application requirements to discuss a suitable configuration and the information needed for a quotation.

The company is the world’s best brushed spur gear motor supplier. We are your one-stop shop for all needs. Our staff are highly-specialized and will help you find the product you need.